Advances in Engineering Advances in Engineering features breaking research judged by Advances in Engineering advisory team to be of key importance in the Engineering field. Papers are selected from over 10,000 published each week from most peer reviewed journals.
-
Dramatic Drop in Cell Resistance through Induced Dipoles and Bipolar Electrochemistry
-
Friction Factor Distribution at the Side Wall of a Turbulent Agitated Vessel with Baffles Using a MAXBLEND Impeller
-
A New Flash Graphene Method
-
Electrochemical Formation of Elemental Boron in LiCl–KCl–KBF4 at 723 K
-
Aminosilane-Grafted SiO2-ZrO2 Polymer Hollow Fibers as Bifunctional Microfluidic Reactor for Tandem Reaction of Glucose and Fructose to 5-Hydroxymethylfurfural
-
Screening Drugs for Glaucoma: a 3D Culture Model of the Trabecular Meshwork
-
Microbubbles and organic fouling in flat sheet ultrafiltration membranes
-
Photopolymerization of Patterned and Multilayer Thin Films for Organic Optoelectronics
-
Fabrication and Performance of Novel Poly(piperazine-amide) Composite Nanofiltration Membranes Based on Various Poly(m‑phenylene isophthalamide) Substrates
-
Ionometallurgical Step-Electrodeposition of Zinc and Lead and its Application in a Cycling-Stable High-Voltage Zinc-Graphite Battery
-
Producing Value‐Added Chemicals from Polyester and Polycarbonate Waste
-
Development of an off‐grid solar‐powered autonomous chemical mini‐plant for producing fine chemicals
-
Carbon [email protected] solar evaporators with controllable salt-tolerance for efficient water evaporation in a closed system
-
Upstream-flow-based mechanisms for global flow regime transition of gas/liquid two-phase flow in pipeline-riser systems
-
Leakage reduction by optimization of hole-pattern damping seal with inclined hole cavity
-
Promotion of ferrofluid microchannel flows by gradient magnetic fields
-
Exact solutions for steady granular flow in vertical chutes and pipes
-
Investigation of transient heat transfer in multi-scale PCM composites using a semi-analytical model
-
3D direct numerical simulation of the entire pool boiling curve from onset of nucleation to critical heat flux through transition boiling to film boiling
-
There is no critical mass ratio for galloping of a square cylinder under flow
-
Mechanical and tribological properties of WO2.9 and ZrO2 + WO2.9 composites studied by nanoindentation and reciprocating wear tests
-
Direct numerical simulations of moisture transport in porous media by a multi-component/phase-change lattice Boltzmann method
-
A Richtmyer–Meshkov instability analog in granular materials with distinct nature
-
Rheological behaviors of media and material removal mechanism for abrasive flow machining micro structures and corresponding simulations
-
A robust and efficient method to facilitate phase change energy storage system simulation
-
A physics-preserving tool for multiphase flow modeling
-
The temperature-dependent thermoelastic problem of elliptic inhomogeneity embedded in infinite matrix
-
Design and optimization of a hybrid battery thermal management system for electric vehicle based on surrogate model
-
Rapid fabrication of frescoes using a geomimetic ceramic formation process
-
Tough nanocomposite polymer hydrogels using silica and clay nanoparticles as fillers
-
Superwettability provides Self-Cleaning and Dynamic Color Response for (Optical) Metasurfaces
-
Powering Entire Cities through Urban Photovoltaics
-
Mechanically Flexible and Optically Tunable Organic Crystal Resonator
-
Efficiently Regulating the Electrical Properties of Flexible Fabric-Based Cu3(BTC)2 Thin Film by Introducing Various Guest Molecules
-
High-Throughput Rapid Experimental Alloy Development (HT-READ)
-
Non-uniform electric field in cantilevered piezoelectric energy harvesters: An improved distributed parameter electromechanical model
-
Extracting true stresses and strains in tensile testing
-
Supervariate Ceramics: Gelatinous and Monolithic Ceramics Fabricated under Ambient Conditions
-
A Puncture-Resistant and Self-Healing Conductive Gel for Multifunctional Electronic Skin
-
Novel 3D printing filament composite using diatomaceous earth and polylactic acid for materials properties and cost improvement
-
Kirigami Reconfigurable Gradient Metasurface
-
Cadmium telluride waveguide for coherent MIR supercontinuum generation covering 3.5-20 µm
-
Slope-assisted Raman distributed optical fiber sensing
-
What can it bring from the joint operation of the joint operation of nuclear and battery energy stations?
-
Digital-optical computational imaging capable of end-point logic operations
-
28.3% Efficient III–V Tandem Solar Cells Fabricated Using a Triple-Chamber Hydride Vapor Phase Epitaxy System
-
Top-down fabricated Ge based reconfigurable transistor
-
Efficient linear predictive model for Li-ion batteries State of Health Estimation
-
Highly Efficient Water Purification System Made Of Solar Nanowire-Nanotube Filter
-
Synchronous construction of piezoelectric elements and nanoresistance networks to achieve flexible micro/nanoscale sensors
-
Tracking Twin Boundary Jerky Motion at Nanometer and Microsecond Scales
-
A Facile and Scalable Method of Fabrication of Large-Area Ultrathin Graphene Oxide Nanofiltration Membrane
-
Bending Stiffness-Directed Fabricating of Kevlar Aerogel-Confined Organic Phase-Change Fibers
-
Building the second floor of flatland: Graphene on hexagonal boron nitride
-
Functionalized gold-nanoparticles enhance photosystem II driven photocurrent in a hybrid nano-bio-photoelectrochemical cell
-
Study of the instantaneous changes in electrical behavior of CNT epoxy composites observed under in-situ simulated space environments
-
A new woody composite is as hard as bone and as tough as aluminum
-
Incorporating nanomaterials to make smart cement improves water and fracture resistance
