Carbon Nanotube-Coated Sand Enables Damage-Sensitive Cement Mortar

Significance 

Cement-based materials are used in buildings, bridges, roads, and other infrastructure. Over time, repeated loading and environmental exposure can cause cracks to develop, gradually affecting their structural integrity. Detecting damage early helps engineers assess the condition of structures and prevent further deterioration. One method is to develop materials that can monitor mechanical loading through changes in their electrical resistance.

These materials, known as self-sensing cementitious composites, contain conductive additives such as carbon nanotubes, carbon fibers, or graphene. Under compression, the conductive particles generally come into closer contact which permit electricity to flow more easily and reducing resistance, a behavior known as negative piezoresistivity.

The difficulty is that cracking can produce the opposite effect and small cracks often form in the interfacial transition zone (ITZ), the region between aggregate particles and the surrounding cement matrix. As these cracks grow, they can disrupt electrical pathways and increase resistance. However, this local increase may be masked by the overall decrease caused by compression which make detection of early damage difficult.

Moisture is another challenge. Electricity can flow through conductive additives by electron transport or through water-filled pores by ion movement and changes in moisture content can affect resistance even when the applied load remains unchanged making the sensing signal less reliable.

Creating conductive pathways in areas where cracks are likely to develop could detect damage more directly. To explore the idea, Harbin Institute of Technology researchers Dr. Zhuo Tang, Dr. Han Xie, Dr. Yumin Guo, Dr. Yipu Guo, and Professor Jing Zhong developed a self-sensing cement mortar using sand particles coated with carbon nanotubes (CNTs). Their study, published in Carbon, examined how CNT content and the sand-to-binder ratio influence electrical conductivity, compressive strength, and sensitivity to internal damage.

The researchers prepared conductive sand by attaching CNTs to quartz particles using a polyacrylate emulsion as a bonding agent. Heating and mixing allowed the nanotubes to adhere to the sand surface without requiring a separate dispersion process. The coated particles were then incorporated into mortar at different CNT concentrations and mixture proportions.

The authors conducted microscopic examination which showed that increasing CNT content improved coverage of the sand particles. They reported at higher concentrations, the coating became more continuous, allowing additional electrical connections to form along their surfaces. They also performed resistance measurements which confirmed that the sand became much more conductive as these connections developed. The nanotubes stayed attached after ultrasonic treatment, showing that the polymer held them firmly on the sand surface.

The nanotubes also influenced the connection between the sand and surrounding cement. Microscopic images showed close contact between the materials, along with interlocking structures that could help strengthen the interface. Further examination identified a composite layer containing CNTs and cement hydration products. The researchers proposed that the polyacrylate coating helped water and calcium ions enter the porous nanotube structure, encouraging hydration products to form within it. This process may have contributed to stronger bonding between the sand and cement matrix.

At a suitable CNT concentration, the mortar achieved a 21.7% increase in compressive strength after 28 days compared with the control. However, adding more nanotubes beyond this concentration reduced the strength. The team attributed this decline to reduced direct contact between the polymer and cement hydration products, which weakened the interfacial reinforcement.

The amount of sand also had a clear influence on the material’s properties and increasing the sand-to-binder ratio brought the coated particles closer together, making it easier for their conductive layers to connect. Microscopic measurements confirmed that the average distance between neighboring particles decreased considerably as the sand content increased. However, these mixtures became less workable and developed more pores, which reduced their compressive strength. This created a balance between improving electrical conductivity and maintaining the mortar’s mechanical properties.

When the coated sand particles were relatively far apart, electrical conduction depended mainly on ions moving through the cement matrix. As the particles moved closer together, their CNT coatings could form continuous pathways for electron transport. With sufficient nanotube coverage, this became the dominant conduction mechanism.

Drying experiments provided further evidence of this change and mortars that relied heavily on ionic transport showed noticeable changes in resistance as moisture was removed. In contrast, mixtures with well-connected CNT networks maintained relatively stable electrical properties during drying.

The most distinctive behavior appeared during repeated compression tests where several mixtures containing CNT-coated sand showed positive piezoresistivity, meaning their electrical resistance increased as compressive stress increased. This response occurred at loading levels well below the material’s ultimate compressive strength, where small cracks could already begin to develop at the aggregate–cement interface.

Microscopic observations helped explain this unusual behavior. Small cracks were found within the CNT–hydration product composite layer near the aggregate surface. Because this layer formed part of the electrical network, cracking could interrupt conductive connections and increase resistance. The location of these cracks supported the researchers’ interpretation that interfacial damage contributed to the positive piezoresistive response.

The magnitude and direction of the electrical response depended on the mixture composition. Mortars with poorly connected networks generally showed weak, negative piezoresistivity, whereas mixtures with more effective connections produced much stronger positive responses. The maximum fractional change in resistivity reached 40%, with a peak stress sensitivity of 14.67% per MPa. The highest sensitivity exceeded the values reported for the conventional self-sensing composites considered in the paper.

Positive piezoresistivity was also observed in mortar without CNT-coated sand. A mixture with high sand content showed an increase in electrical resistance under compression even though no nanotubes were present. The researchers attributed this behavior to the close spacing of sand particles, which created regions dominated by vulnerable interfaces where small cracks could interrupt ionic conduction.

During repeated loading tests, some mixtures showed differences in electrical resistance between compression and unloading, consistent with internal structural changes that were not fully reversible. Other mixtures followed more closely overlapping curves, indicating greater stability of the conductive network. Despite these differences, resistance generally followed the applied stress during repeated cycles, demonstrating the mortar’s ability to monitor mechanical loading.

Professor Jing Zhong and colleagues also examined the practicality of producing the coated aggregates. The preparation involved mainly heating and mixing, without the need for complex nanotube dispersion techniques or specialized high-temperature treatment. Their cost analysis estimated relatively low production costs which is a significant advantage.

Overall, the study by Harbin Institute of Technology scientists provides a new approach to designing cement-based materials that combine mechanical strength with sensitivity to internal damage. The arrangement of conductive aggregates influences both how electricity moves through the mortar and how its resistance changes when interfacial cracks develop. This relationship can guide the design of self-sensing materials for structural health monitoring.

Reference

Zhuo Tang, Han Xie, Yumin Guo, Yipu Guo, Jing Zhong, Positive piezoresistive mortar based on carbon nanotube adhered aggregates: Damage at interfacial transition zone and mechanism, Carbon, Volume 253, 2026, 121417,

Go to Carbon 

Check Also

Recovering Weak Borehole Reflections Without Labeled Training Data

Significance  Reference Qiang Wang, Hua Wang, Zhilong Fang, Qizhi Bi, An unsupervised deep learning method …