Significance
Deep saline aquifers could provide the underground space needed to store large quantities of hydrogen. These formations consist of porous rock filled with saline water and covered by relatively impermeable layers that help prevent gas from escaping. When hydrogen is injected, it displaces some of the brine and occupies the pore spaces within the rock. Their widespread distribution makes them attractive for large-scale energy storage.
However, the available pore space alone does not determine how much hydrogen an aquifer can accommodate. Injection increases pressure within the formation, and excessive pressure can fracture the rock, reactivate existing faults, or damage the overlying seal. The amount of hydrogen that can be introduced is therefore limited by the reservoir’s response to injection.
Hydrogen has low density and viscosity which also affect how it moves through the reservoir. Some hydrogen can dissolve in formation water and gradually diffuse through the surrounding rock or the overlying caprock. Microorganisms may also consume hydrogen through metabolic reactions, reducing the amount retained underground.
Estimating storage capacity requires accounting for these processes without relying on overly complicated calculations. Simple estimates based on pore volume can overlook pressure restrictions and hydrogen losses. Detailed numerical simulations provide a more complete picture of fluid movement, but they require extensive geological information and computing resources that may not be available during preliminary site assessments.
Rock permeability, reservoir thickness, well spacing, and injection duration can all affect storage performance and understanding how all these factors interact is important when evaluating potential storage sites and planning injection strategies. In a recent research paper published in Energy Conversion and Management, Dr. Chuanjie Ren, Dr. Xiaojiang Li, Dr. Ziqing Pan, and Professor Kaiqiang Zhang from Peking University developed a new analytical method to estimate hydrogen storage capacity in deep saline aquifers. They applied it to a representative aquifer in the Northern North Sea to examine how geological properties, engineering decisions, and potential hydrogen losses influence storage capacity.
Experiments and Findings
The researchers first examined how hydrogen injection affects pressure within an aquifer. They considered both open reservoirs, where pressure can spread over a large area, and closed reservoirs, where impermeable boundaries restrict its movement. From these calculations, they determined the maximum injection rates that would keep pressure below levels associated with rock fracturing or fault reactivation.
The proposed method also accounted for the properties of hydrogen and brine, the number and spacing of injection wells, and their operating limits. The researchers assessed potential hydrogen losses from microbial consumption, dissolution into saline water, and subsequent diffusion through the surrounding rock. They used conservative assumptions to establish upper-bound estimates of these losses rather than predict their actual magnitude at a particular site.
The team then applied the method to geological data from a saline aquifer in the Northern North Sea. The selected formation was approximately 3,523 metres deep, with a thickness of about 646 metres and a porosity of 16%. They explored how changing the number and spacing of injection wells affected storage capacity.
Increasing the number of wells generally allowed more hydrogen to be stored, although the maximum injection rate decreased. Pressure buildup around neighbouring wells can overlap, making the distance between them an important consideration. For the selected aquifer, the highest calculated storage capacity was approximately 1.5 billion tonnes of hydrogen, achieved with 10 wells spaced about 5.2 kilometres apart under the model’s pressure and geometric constraints.
The researchers also compared hydrogen and carbon dioxide storage in the same aquifer. Despite their considerable differences in physical properties, the calculated storage performance differed by only about 0.5%. Hydrogen is much less dense than carbon dioxide, but its greater volumetric injectivity helped compensate for this difference, producing a similar calculated storage capacity by mass. This close agreement depended on the reservoir conditions and assumptions used in the comparison and may not occur in other formations.
Chuanjie Ren et al. also examined how reservoir properties influenced hydrogen storage capacity and reported that greater thickness, permeability, porosity, and rock and brine compressibility generally contributed to higher calculated storage capacity. Thicker and more permeable formations allow fluids to move more easily, reducing pressure buildup during injection. Higher porosity provides more pore space, while greater compressibility may allow the reservoir to accommodate additional injected fluid within the prescribed pressure limit.
However, these improvements had limits. Beyond a certain point, increasing these properties offered little additional benefit because other factors, such as the maximum injection capacity of the wells, became limiting. For example, once a reservoir can support injection at the wells’ maximum capacity, increasing its permeability further provides little advantage.
The properties of hydrogen and brine also affected storage performance. They noticed higher hydrogen density increased the calculated storage capacity, whereas greater hydrogen or brine viscosity reduced injectivity by increasing resistance to flow. Lower viscosity improved injectivity, but the benefit eventually levelled off. Brine salinity had relatively little influence under the conditions examined.
Operating time was another important factor in their studies and the authors found longer injection periods generally increased the total amount of hydrogen that could be stored, even though the maximum average annual injection rate decreased. The researchers extended their calculations to 1,000 years to investigate the theoretical upper limit of storage capacity as pressure spreads through the formation and approaches its limiting behaviour. This extended period was used to explore the mathematical limits of the model, not to propose a realistic operating schedule.
Significance and Implications
The study by Peking University scientists provides an important and practical way to estimate hydrogen storage capacity during the early stages of evaluating saline aquifers. Instead of relying only on available pore volume, the method considers how much hydrogen can be injected within geological and engineering constraints. This allows potential storage sites to be assessed using an analytical approach before more detailed reservoir simulations are undertaken.
Their new method allows engineers to examine how different restrictions influence storage performance and improving reservoir conditions or changing the number and spacing of wells may increase capacity, but the benefits depend on which factor is limiting injection. Understanding these relationships can help engineers select suitable operating conditions and identify where adjustments to a proposed storage design would be most useful.
The method also incorporates potential hydrogen losses that are not captured by simple volumetric estimates. Accounting for microbial consumption, dissolution, and diffusion provides a more realistic basis for preliminary capacity assessment, although the estimated losses remain theoretical bounds rather than predictions of actual hydrogen recovery.
The analytical approach is intended for basin-scale screening, where the main objective is to estimate potential capacity and compare engineering options. Detailed reservoir simulations and site-specific investigations remain essential for evaluating fluid movement, long-term containment, well and caprock integrity, operational cycling, and recovery performance. The screening method can help guide those investigations by identifying the geological conditions and injection strategies that deserve closer examination.
Reference
Chuanjie Ren, Xiaojiang Li, Ziqing Pan, Kaiqiang Zhang, Underground hydrogen storage capacity in saline aquifer, Energy Conversion and Management, Volume 353, 2026, 121195, https://doi.org/10.1016/j.enconman.2026.121195
Advances in Engineering Advances in Engineering features breaking research judged by Advances in Engineering advisory team to be of key importance in the Engineering field. Papers are selected from over 10,000 published each week from most peer reviewed journals.



